Castaldo SuperCera Jewelry Injection Wax

 

Ceras de calidad superior, para una amplia gama de aplicaciones, en una nueva forma única en su género, más conveniente y de fácil identificación.

Hechas de ingredientes naturales al 100%, son filtradas tres veces para asegurar la ausencia de problemas. No obstruyen la boquilla del inyector.

Seguras - No tóxicas - No causan peligro.

Se queman en el horno al 100% - sin residuos de ceniza.

Contienen un agente quimico para facilitar la extracción del molde, haciendo más sencillo el desmoldeo.

Una gama completa de ceras para todas las necesidades:

Aqua

Extremely flexible. Excellent for intricate filigree and difficult pieces. Inject at 165°F/74°C.

Orange

Very flexible and easy flowing with excellent memory and minimal sink. Good all purpose wax; also recommended for pieces with thin areas. Inject at 155°F/68°C.

Red

An all purpose wax; for a wide variety of pieces. Cools quickly. Medium flexibility. Inject at 165°F/74°C.

Gold

Hard with very little flexibility. Flows easily. Will hold sharp detail. Almost no shrinkage or sink. Can be carved. Recommended for large patterns with fine detail. Also good for metal molds. Inject at 170°F/76°C.

Green

Flexible with a slow cooling time. Minimal shrinkage. Very little sink. Excellent for large flat pieces or as a general purpose wax. Inject at 150°F/65°C.



Disponible en cartones de 22,7 kg.
También se suministra en convenientes cajas de 2,27 kg. Se despachan en cartones que contienen 12 cajas de 2,27 kg. Peso neto total: 27,3 kg.

Choosing the right Castaldo SuperCera Jewelry Injection Wax

Color

Flexibility

Fill

Minimal Shrinkage

Minimal Sink

Use For: Large Flat Pieces

Use For: Intricate Thin or Difficult Pieces

Use For: All Purpose

Can Be Carved

Aqua

xxx

xxx

-

-

-

xxx

-

-

Orange

xx

xx

x

-

-

xx

x

-

Red

-

x

xx

x

x

-

xx

x

Gold

-

-

xxx

xxx

xxx

x

-

xx

Green

x

xx

xxx

xx

xxx

xx

x

x



Wax injection problems and solutions

Air Bubbles In Pattern

• Not enough wax in pot

• Refill pot

• Wax too hot or too cold

• Adjust wax temperture

• Poor contact between mold and  injection nozzle

• Hold mold properly

• Too much air pressure

• Reduce air pressure

Mold does not fill

• Air pressure too low

• Increase air pressure

• Wax too cold

• Increase wax temperature*

• Cold mold

• Warm up mold by repeated use

• Sprue too narrow

• Widen sprue

• Insufficient mold venting (Air trapped in mold)

• Improve mold vents

• Mold vents sealed, dirty or clogged with wax

• Clean mold vents and keep mold vents open with pewder

• Injector clogged

• Clean injector and injector nozzle

Mold over-fills

• Air pressure high

• Reduce air pressure

• Mold not closed properly

• Hold mold with even pressure
• Recut mold with improved mold locks

• Wax too hot

• Adjust wax temperature*

• Injection time too long

• Reduce injection time

Wax sticky, bends easily

• Mold open too soon

• Lengthen mold holding time

• Wax too hot

• Reduce wax temperature*

Excessive shrinkage

• Wax temperature too high

• Reduce wax temperature*

• Air pressure too low

• Increase air pressure

• Mold holding time too short

• Lengthen mold holding time

• Sprue too narrow

• Widen sprue

• Cold mold

• Warm mold through repeated use

• Low shrinkage wax not selected

• Choose low shrinkage



NOTE:

Each mold and each wax is different in its pressure, temperature and mold holding time requirements. The correct combination of factors can be achieved only through experience with each mold and each wax. For easy future reference these factors should be noted on the mold itself.

In addition, a mold's characteristics change as hot wax is repeatedly injected into it. The correct combination of factors for a cold mold may not be the correct combination of factors for the same mold after it has become warm through repeated use. The cooling time between injections - too much or too little - is thus also a factor.

For best results select the right Castaldo SuperCera wax for the requirements of the mold and to meet production needs. (See wax selection chart).

CAUTION:

Molten injection waxes are FLAMMABLE at temperatures in excess of 350°F/177°C.

CAUTION:

Hot injection waxes can cause skin burns. Avoid contact with skin. Adequate eye protection and protective clothing is strongly recommended.

All Castaldo SuperCera waxes are non-hazardous, non-toxic and non-carcinogenic.

All Castaldo SuperCera waxes are intended for professional use and only by persons familiar with jewelry casting techniques.

We are not responsible for misuse of our products or their use in conjunction with unsafe or improperly maintained equipment.

IMPORTANT NOTICE:

CASTALDO SuperCera Jewelry Injection Waxes are warranted to be free from defects in material and workmanship. THE FOREGOING WARRANTY'S IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES NOT EXPRESSLY SET FORTH HEREIN, WHETHER EXPRESSED OR IMPLIED BY OPERATION OF LAW OR OTHERWISE, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The seller shall not be liable for incidental or consequential losses, damages or expenses, directly or indirectly arising from the sale, handling or use of the goods, or from any other cause relating thereto, and Seller's liability hereunder in any case is expressly limited to the replacement (in the form originally shipped) of goods not complying with this agreement or at Seller's election, to the repayment of, or crediting Buyer with, an amount equal to the purchase price of such goods, whether such claims are for breach of warranty or negligence. Any claim by Buyer with reference to the goods sold hereunder for any cause shall be deemed waived by the buyer unless submitted to Seller in writing within (30) days from the date Buyer discovered, or should have discovered, any claimed breach.


Instrucciones en Inglés
En el Boletín Técnico Inglés
SuperCera Datos técnicos en Inglés
Volver al menú en español
SuperCera® (En İngilizce) GHS EUGHS













 


Copyright © 1991-2016 F. E. Knight Inc. ALL RIGHTS RESERVED